Fire Wrap Fyre Wrap Foil Faced - 1220mm x 7.62m (38mm Insulation) #FYREWRAP1220

Item#: FYREWRAP1220 Category Tag

Price: $1,399.99

FyreWrap is a foil-faced Fire Protection Wrap/Blanket designed to provide
fire rating to Ducts, Kitchen Exhausts, Smoke Spill Systems, Penetration Seals & Structural Steel
Elements.

FyreWrap is FIRE TESTED & APPROVED for up to 3 hours in accordance with
AS1530.4-2005

FyreWrap’s
core materials is Lightweight and has been Highly Engineered with High Temperature
Thermal Insulation material Insulfrax which is made from Calcia, Magnesia & Silica chemistry
designed to enhance Bio-Solubility.

FyreWrap’s Aluminiumn Foil, Fibreglass-Reinforced Scrim
completely encapsulates the core providing additional handling strength, protection from tearing and
most importantly provides High Resistance to Mould Growth.

FyreWrtap is easily Identificed in the field by
Building Certifiers and Engineers

FyreWrtap has had extensive testing to ensure that it
meets the highest quality in terms of impact on Environmental Health.   The material is
completely Bio-Soluble and FyreWrap has been Green-guard listed for Microbial (Mould Growth)
Resistance.

*
Environmentally Friendly (has a Low Environmental
Impact)

*  Quick &
Efficient

*  Clean, Safe & Easy to
Install

*  Off-site Installation is
possible, assisting in effective Project Co-ordination

*  Clear Identification for
FIre Certification & Auditing Purposes

*  Mould
Resistant

*  Vibration
Tolerant

*  No Masking Required, Simple
Repair (tape up or replace section)

*  Lightweight (up to 5x
lighter than traditional fire spray)

*  FyreWrap is .8mm thick
having an R Value of approximately 1.2

USES:  Duct Access Panels,
Dampers, Service Penetration Upgrades & Hard to Reach Areas on
Site

 

a)
For Ducting less
than
600mm x 600mm, a 19mm wide
0.4mm thick
Steel Band is
used to permanently supoort FyreWrap around the Duct.  The Steel Band is placed 40mm from the edge
of the FyreWrap blanket, over the overlaps and one additioanl band between the overlaps at 265mm
centres.

b) 
For Ducting greater than 600mm x 600mm but less than 1200mm x 1200mm, the
Banding System described in a). is used in conjunction with either Pre-welded Pins/Cup Head Style Pins
along the bottom of the duct at 200mm apart.

c)
 For Ducting greater than 1200mm x
1200mm,
either Pre-welded Pins or Cup Head style
Pins
over all 4 sides of Ducyt MUST be Used at 200mm
apart

***PLEASE NOTE – DO NOT USE Self Adhesive
Pins***

 

10 in stock

People also viewed

what our clients say

Warren Hendricks
Read More
Always a pleasure dealing with the team on site. Helpful and friendly service
Sanjiv Brahmbhatt
Read More
Good customer service. They got good fitting for condensor units.
Sanjiv Brahmbhatt
Read More
Good customer service. They got good fitting for condensor units.
Warren Hendricks
Read More
Always a pleasure dealing with the team on site. Helpful and friendly service
Warren Hendricks
Read More
Always a pleasure dealing with the team on site. Helpful and friendly service
Warren Hendricks
Read More
Always a pleasure dealing with the team on site. Helpful and friendly service
Sanjiv Brahmbhatt
Read More
Good customer service. They got good fitting for condensor units.
Sanjiv Brahmbhatt
Read More
Good customer service. They got good fitting for condensor units.
Previous
Next

We are located AT:

113 Mays Road, Onehunga, Auckland 1061

Contact us here

Can’t find what you’re looking for? We can try source it for you! Give us a call on 09 636 5951 now.